49+ Woodworking Plans For Garden
woodworkingplansman.com Introduction: Building Your Own Garden Planter Thinking about adding some life to your garden or patio? Building your own wooden planter is a fantastic, cost-effective way to showcase your favorite plants and flowers. This guide will walk you through the process, step-by-step, making it easy even for beginners. Let's get started!
Materials and Tools You'll Need Before you dive in, gather these essential supplies. This will ensure a smooth and efficient building experience.
- Wood: Choose rot-resistant wood like cedar, redwood, or treated lumber. The amount will depend on your desired planter size. A common size is 24" x 12" x 12", for which you'd need about 12-16 linear feet of lumber.
- Fasteners: Exterior wood screws (1 1/4" to 1 5/8") are recommended for their weather resistance.
- Tools:
- Measuring Tape
- Pencil
- Saw (Circular saw, hand saw, or miter saw)
- Drill with drill bits
- Screwdriver or drill with screw bit
- Sandpaper (Medium and fine grit)
- Safety Glasses
- Work Gloves
- Optional: Wood glue (exterior grade)
- Finishing Supplies (Optional):
- Wood Stain or Paint (exterior grade)
- Wood Sealer (exterior grade)
- Paintbrush or Roller
Step 1: Planning and Cutting the Wood First, decide on the size and shape of your planter. A simple rectangular planter is easiest for beginners. Once you have your dimensions, carefully measure and mark the wood. Use your saw to cut the wood into the following pieces:
- Side Pieces: Two pieces for the sides of the planter (e.g., 24" long if your planter is 24" long).
- End Pieces: Two pieces for the ends of the planter (e.g., 12" long if your planter is 12" wide).
- Bottom Pieces: Cut enough pieces to cover the bottom of the planter (e.g., if you are using 4" wide boards, you may need three boards that are 12" long to cover the bottom). Consider adding a small gap between the bottom boards for drainage.
- Legs (Optional): Four small pieces if you want to raise the planter off the ground.
Step 2: Assembling the Sides Now it's time to assemble the frame of the planter. Attach the Sides and Ends: Place one of the side pieces on its edge. Position an end piece flush against the side piece's edge. Drill pilot holes through the end piece and into the side piece. This prevents the wood from splitting. Apply a bead of wood glue (optional) and then screw the two pieces together. Repeat this process for the other side and end pieces, creating a rectangular box. Check for Square: Before the glue dries (if used), use a square or measuring tape to ensure the box is square. Adjust as needed.
Step 3: Adding the Bottom Attaching the bottom boards is the next step. Attach Bottom Boards: Place the assembled box upside down. Position the bottom boards inside the box frame, spacing them slightly apart for drainage. Drill pilot holes through the bottom boards and into the side and end pieces. Apply a bead of wood glue (optional) and then screw the boards in place. Make sure the screws are flush with the surface or slightly countersunk to avoid snagging anything later.
Step 4: Adding Legs (Optional) If you want to add legs to elevate your planter, now is the time. Attach Legs: Position a leg piece in each corner of the planter box. Drill pilot holes through the legs and into the side and end pieces. Apply a bead of wood glue (optional) and then screw the legs securely in place.
Step 5: Sanding and Finishing Once the planter is assembled, it's time to smooth out any rough edges and apply a protective finish. Sanding: Use medium-grit sandpaper to smooth out any rough edges and imperfections. Then, switch to fine-grit sandpaper for a final smooth finish. Pay particular attention to the corners and edges. Finishing (Optional): If you want to protect the wood and enhance its appearance, apply a coat of exterior wood stain or paint. Allow it to dry completely according to the manufacturer's instructions. Then, apply a coat of exterior wood sealer to protect the wood from moisture and UV damage.
Step 6: Adding Drainage and Planting Before planting, ensure proper drainage. Drainage Holes: If you didn't leave gaps between the bottom boards, drill several drainage holes in the bottom of the planter. Lining (Optional): Line the inside of the planter with landscape fabric to prevent soil from washing out and to prolong the life of the wood. Planting: Fill the planter with a good quality potting mix and plant your favorite flowers, vegetables, or herbs.
Conclusion: Enjoy Your New Garden Planter! Congratulations! You've successfully built your own wooden garden planter. Now you can enjoy the beauty of your plants and the satisfaction of knowing you created something yourself. This planter will add a touch of charm to your garden or patio for years to come. Remember to maintain your planter by re-sealing it every few years to protect the wood from the elements. Happy gardening!
Garden Woodworking Plans • Just Wood It!
justwood.it Simple Garden Woodworking Plans
howcanthis.com Garden Free Woodworking Plans
woodworkingplansman.com
0 komentar:
Posting Komentar